Your cart is empty

New Products - more

751002 New PILZ PNOZ s Setspring loaded terminals 12,5mm

$45.00 $22.00
Save: 51% off

750910 New PILZ PNOZ s nIE

$113.00 $55.00
Save: 51% off

750900 New PILZ PNOZ s pIE

$113.00 $55.00
Save: 51% off

Reviews - more

Write a review on this product.

Information

Home :: Rosemount Transmitter :: EJA438E-FASCG-919DB-WA12C2HW00-1A29/KS26/X2/D3/N4/M2W/T52 New Yokogawa EJA438E Diaphragm Sealed Differential Pressure Transmitter

Product 818/1465

Return to the Product List

EJA438E-FASCG-919DB-WA12C2HW00-1A29/KS26/X2/D3/N4/M2W/T52 New Yokogawa EJA438E Diaphragm Sealed Differential Pressure Transmitter

$7,755.00 $3,800.00
Save: 51% off

Part Number: EJA438E-FASCG-919DB-WA12C2HW00-1A29/KS26/X2/D3/N4/M2W/T52

Model: EJA438E Diaphragm Sealed Differential Pressure Transmitter

Brand: Yokogawa

Condition: New & Original in Factory Packing

Factory Warranty: 12 Months

Ordering Information

Model	EJA438E	Diaphragm sealed gauge pressure transmitter
Output signal	-F	Digital communication (FOUNDATION Fieldbus protocol, refer to GS 01C31T02-01EN)
Measurement span (capsule)	A	0.06 to 3.5 MPa (8.6 to 500 psi)
	S	Always S
	C	Always C
Coverflange bolts and nuts material	G	316L SST
Installation	-9	Horizontal piping type and left side high pressure
Amplifier housing	1	Cast aluminum alloy
Electrical connection	9	M20 female, two electrical connections with a blind plug⁽¹⁾
Integral indicator	D	Digital indicator⁽²⁾
Mounting bracket	B	304 SST 2-inch pipe mounting, flat type (for horizontal piping)
Process connection style	-W	Flush type
Flange rating	A1	ANSI class 150
Process connection size (Process flange size)	2	2-inch (50 mm)
Flange material	C	316 SST⁽³⁾
Gasket contact surface⁽⁴⁾	2	Flat (no serration)
Wetted parts material⁽⁵⁾	HW	Diaphragm: Hastelloy C-276^(6)# Others: Hastelloy C-276^(6)#
Flushing connection ring⁽⁷⁾	*0	Ring: None Vent/Drain plugs: - Material: -
Extension	0	None
Fill fluid	-1	High temp. and high vacuum use (Silicone oil)⁽⁸⁾⁽⁹⁾
Capillary connection	A	Side of diaphragm seal unit
	2	Always 2
Capillary length⁽¹⁰⁾	9	9 m
	/KS26
Painting	/X2	Coating change: Anti-corrosion coating⁽¹¹⁾
Calibration units⁽¹²⁾	/D3	bar calibration (bar unit)
Wired tag plate	/N4	316 SST tag plate wired onto transmitter (Tag No.: Maximum. 16 characters.)
Material certificate	/M2W	Process flange, Block
Pressure test/Leak test certificate^(13)(14)	/T52	For A-Capsule Flange rating: ANSI/JPI Class 150 Test pressure: 3 MPa (430 psi)

The ??*?? marks indicate the most typical selection for each specification.

Material of a blind plug; aluminum alloy for code 5 and 9, and SUS304 for code 7.
Not applicable for output signal code G.
Forged version of the material may be used.
See table 3 ??Gasket contact surface?? on page 5.
Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user??s process fluids.
Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and hightemperature steam (150??C [302??F] or above). Contact Yokogawa for detailed information of the wetted parts material.
In case of wetted parts material code HW (Hastelloy C), TW (Tantalum), and UW (Titanuym) for 2-inch pressure flange, specify capillary length from 1 to 5 m.
When specified flushing connection ring code A or B, exclusive gasket is provided for transmitter side.
In case of wetted parts material code TW (Tantalum), the process temperature limit is ?C10 to 200??C.
Not applicable for wetted parts material code UW.
In case of wetted parts material code HW (Hastelloy C), TW (Tantalum), and UW (Titanuym) for 2-inch pressure flange, specify capillary length from 1 to 5 m.
Not applicable with color change option. Not applicable for amplifier housing code 2.
The unit of MWP (Max. working pressure) on the name plate of a housing is the same unit as specified by option code D1, D3, and D4.

The ??#??marks indicate the construction materials conform to NACE material recommendations per MR0175/ISO 15156. Please refer to the latest standards for details. Selected materials also conform to NACE MR0103.

Estimated Lead Time: 8 - 12
Shipping Weight: 20 Kg

Add to Cart: