Your cart is empty

New Products - more

0521322 New Hengstler

$302.00 $180.00
Save: 40% off

0521321 New Hengstler

$339.00 $202.00
Save: 40% off

0521320 New Hengstler

$339.00 $202.00
Save: 40% off

Reviews - more

Write a review on this product.

Information

Home :: Rosemount Transmitter :: EJA118E-FMSCG-937DB-WA22C1SW00-AA2A/CF1 New Yokogawa EJA118E Diaphragm Sealed Differential Pressure Transmitter

Product 718/1465

Return to the Product List

EJA118E-FMSCG-937DB-WA22C1SW00-AA2A/CF1 New Yokogawa EJA118E Diaphragm Sealed Differential Pressure Transmitter

$5,063.00 $2,481.00
Save: 51% off

Part Number: EJA118E-FMSCG-937DB-WA22C1SW00-AA2A/CF1

Model: EJA118E Diaphragm Sealed Differential Pressure Transmitter

Manufacturer: Yokogawa

Condition: New & Original in Factory Packing

Factory Warranty: 12 Months

Description

The EJA-E series of transmitters is Yokogawa's most recent evolution of the DPharp family. Released in 2012, it combines the ruggedness and success of the work-horse EJA-E series with the performance of the thoroughbred EJX-A series to deliver the type of product you have come to expect from Yokogawa.

The EJA118E is a Differential Pressure Transmitter with remote diaphragm seals.

EJA118E features include:

??0.2% Accuracy
200 ms Response Time
Exida and TUV SIL2 / SIL3 Certified
Local Parameter Setting (LPS)
10-segment Signal Characterizer
Active Capillary Fill Fluid Density Compensation

Model and Suffix Codes

Model	EJA118E	Diaphragm sealed differential pressure transmitter
Output signal	-F	Digital communication (FOUNDATION Fieldbus protocol, refer to GS 01C31T02-01EN)
Measurement span (capsule)	M	2.5 to 100 kPa (10 to 400 inH₂O)
	S	Always S
	C	Always C
Cover flange bolts and nuts material	G	316L SST
Installation	-9	Horizontal piping type and left side high pressure
Amplifier housing	3	Cast aluminum alloy with corrosion resistance properties⁽¹⁾
Electrical connection	7	1/2 NPT female, two electrical connections with a blind plug⁽²⁾
Integral indicator	D	Digital indicator⁽³⁾
Mounting bracket	B	304 SST 2-inch pipe mounting, flat type (for horizontal piping)
Process connection style	-W	Flush type
Flange rating	A2	ANSI class 300
Process connection size (Process flange size)	2	2-inch (50 mm)
Flange material	C	316 SST⁽⁴⁾
Gasket contact surface⁽⁵⁾	1	Serration (for ANSI flange with wetted parts material SW only)
Wetted parts material⁽⁶⁾	SW	[Diaphragm] 316L SST [Pipe] 316L SST [Others] 316L SST
Flushing connection ring⁷⁾	0	[Ring] None [Vent/Drain plugs] - [Material] -
Extension	0	None
Fill fluid⁽⁸⁾	-A	For general use (silicone oil)⁽⁹⁾ [Process temperature] ?C10 to 250??C [Ambient temperature] ?C10 to 60??C
Capillary connection	A	Side of diaphragm seal unit
	2	Always 2
Capillary length⁽¹⁰⁾	A	10 m
Canadian Standards Association (CSA)	/CF1	CSA Explosionproof Approval⁽¹¹⁾ Certificate: 2014354 Applicable Standard: C22.2 No. 25, C22.2 No. 30, CAN/CSA-C22.2 No. 94, CAN/CSA-C22.2 No. 61010-1, CAN/CSA-C22.2 No. 61010-2-030, CAN/CSA-C22.2 No. 60079-0, CAN/CSA-C22.2 No. 60079-1, CAN/CSA-C22.2 No. 60529 Explosion-proof for Class I, Groups B, C and D. Dustignition-proof for Class II/III, Groups E, F and G. When installed in Division 2, ??SEAL NOT REQUIRED?? Enclosure: Type 4X, Temp. Code: T6...T4 Ex d IIC T6...T4 Enclosure: IP66/IP67 Max.Process Temp.: T4;120??C(248??F), T5;100??C(212??F), T6; 85??C(185??F) Amb.Temp.: ?C50 to 75??C(?C58 to 167??F) for T4, ?C50 to 80??C(?C58 to 176??F) for T5, ?C50 to 75??C(?C58 to 167??F) for T6⁽¹²⁾ Process Sealing Certification Dual Seal Certified by CSA to the requirement of ANSI/ISA-12.27.01 No additional sealing required Primary seal failure annunciation: at the zero adjustment screw

The ??*?? marks indicate the most typical selection for each specification

Not applicable for electrical connection code 0, 5, 7, 9 and A.
Material of a blind plug; aluminum alloy for code 5 and 9, and SUS304 for code 7.
Not applicable for output signal code G.
Forged version of the material may be used.
See table 3 ??Gasket contact surface?? on page 6.
Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user??s process fluids.
Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and hightemperature steam (150??C [302??F] or above). Contact Yokogawa for detailed information of the wetted parts material.
When specified flushing connection ring code 1 or 2, exclusive gaskets are provided for transmitter side.
Even in case where fill fluid code D (fluorinated oil) is selected, if degrease cleansing treatment or both degrease cleansing and dehydrating treatment for the wetted parts is required, specify option code K1 or K5.
In case of wetted parts material code TW (Tantalum), the process temperature limit is ?C10 to 200??C.
In case of wetted parts material code HW (Hastelloy C) and TW (Tantalum) for 2-inch process flange, specify capillary length from 1 to 5m.
Applicable for Electrical connection code 2, 4, 7, 9, C and D.
Lower limit of ambient temperature is ?C15??C (5??F) when /HE is specified.

Estimated Lead Time: 12 - 16
Shipping Weight: 10 Kg

Add to Cart: