Your cart is empty

New Products - more

NKTT01-3 New ABB Bailey Infi-Net Termination Cable

$112.00 $67.00
Save: 40% off

NTCF23 New ABB Bailey Fiber Optic Communication Termination Unit

$5,062.00 $3,012.00
Save: 40% off

NTCF22 New ABB Bailey INFI-Net Optic-to-Electric Termination Unit

$6,800.00 $3,798.00
Save: 44% off

Reviews - more

Write a review on this product.

Information

Home :: Rosemount Transmitter :: EJX118A-FMSCG-919DJ-WA23C2HW00-AA24/KS26/D3/TF1 New Yokogawa EJX118A Differential Pressure Transmitter

Product 935/1465

Return to the Product List

EJX118A-FMSCG-919DJ-WA23C2HW00-AA24/KS26/D3/TF1 New Yokogawa EJX118A Differential Pressure Transmitter

$9,252.00 $4,534.00
Save: 51% off

Part Number: EJX118A-FMSCG-919DJ-WA23C2HW00-AA24/KS26/D3/TF1

Model: EJX118A Differential Pressure Transmitter

Manufacturer: Yokogawa

Condition: New & Original in Factory Packing

Factory Warranty: 12 Months

Ordering Information

Model	EJX118A	Diaphragm sealed differential pressure transmitter
Output signal	-F	Digital communication (FOUNDATION Fieldbus protocol, refer to GS 01C25T02-01EN)
Measurement span (capsule)	M	2 to 100 kPa (8 to 400 inH2O)
	S	Always S
	C	Always C
Coverflange bolts and nuts material	G	316L SST
Installation	-9	Horizontal piping type and left side high pressure
Amplifier housing	1	Cast aluminum alloy
Electrical connection	9	M20 female, two electrical connections with a blind plug⁽¹⁾
Integral indicator	D	Digital indicator⁽²⁾
Mounting bracket	J	316 SST 2-inch pipe mounting, flat type (for horizontal piping)
Process connection style	-W	Flush type
Flange rating	A2	ANSI class 300
Process connection size (Process flange size)	3	3-inch (80 mm)
Flange material	C	316 SST⁽³⁾
Gasket contact surface⁽⁴⁾	2	Flat (no serration)
Wetted parts material⁽⁵⁾	HW	[Diaphragm] Hastelloy C-276^(6)# [Others] Hastelloy C-276^(6)#
Flushing connection ring⁽⁷⁾	?0	[Ring] None [Vent/Drain plugs] - [Material] -
Extension	0	None
Fill fluid⁽⁸⁾	-A	For general use (silicone oil)⁽⁹⁾ [Process temperature] ?C10 to 250??C [Ambient temperature] ?C10 to 60??C
Capillary connection	A	Side of diaphragm seal unit
	2	Always 2
Capillary length⁽¹⁰⁾	4	4 m
	/KS26
Calibration units⁽¹¹⁾	/D3	bar calibration (bar unit)
Teflon film⁽¹²⁾⁽¹³⁾⁽¹⁴⁾	/TF1	Diaphragm protection from sticky process fluid by FEP Teflon film attached with fluorinated oil. Operation range: 20 to 150??C, 0 to 2 MPa (Not applicable for vacuum service).

The ????? marks indicate the most typical selection for each specification.

Material of a blind plug; aluminum alloy for code 5 and 9, and SUS304 for code 7.
Not applicable for output signal code G.
Forged version of the material may be used.
See table 3 ??Gasket contact surface?? on page 6.
Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user??s process fluids.
Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and hightemperature steam (150??C [302??F] or above). Contact Yokogawa for detailed information of the wetted parts material.
Hastelloy C-276 or N10276.
When specified flushing connection ring code 1 or 2, exclusive gaskets are provided for transmitter side.
Even in case where fill fluid code D (fluorinated oil) is selected, if degrease cleansing treatment or both degrease cleansing and dehydrating treatment for the wetted parts is required, specify option code K1 or K5.
In case of wetted parts material code TW (Tantalum), the process temperature limit is ?C10 to 200??C.
In case of wetted parts material code HW (Hastelloy C) and TW (Tantalum) for 2-inch process flange, specify capillary length from 1 to 5m.
The unit of MWP (Max. working pressure) on the name plate of a housing is the same unit as specified by option code D1, D3, and D4.
Applicable for flush type (process connection style code W.)
Applicable for flushing connection ring code 0.
Not applicable for Fill fluid code 1, 2, or 4.

Estimated Lead Time: 8 - 12
Shipping Weight: 8 Kg

Add to Cart: